How To Change The Battery In A Moto G5 Plus

Introduction

Utilise this guide to supplant the lithium-ion battery in your Motorola Moto G5 Plus. With daily use, a typical bombardment will last around 18-24 months earlier losing significant capacity. If your battery no longer holds a full charge or is causing unexpected shutdowns, yous can follow the instructions below to restore your phone to good working order.

Before disassembling your phone, discharge the battery below 25%. A charged lithium-ion battery tin catch fire and/or explode if accidentally punctured.

If your battery is swollen, do not estrus your phone and take appropriate precautions. If needed, y'all can apply a dropper or syringe to inject isopropyl alcohol (90+%) around the edges of the display to weaken the adhesive. Swollen batteries tin can be very unsafe, and so article of clothing center protection and practise due circumspection, or take it to a professional if you're non sure how to proceed.

• Be certain to ability off your phone before you lot brainstorm.

• Apply a SIM eject bit, SIM squirt tool, or paper prune to remove the SIM card from your phone.



• Prepare an iOpener and heat the front of the telephone forth its left edge for about two minutes, or until it'southward slightly too hot to touch on. This will help soften the adhesive securing the display.

• You lot may need to reheat and reapply the iOpener several times to get the phone warm enough to cutting the agglutinative. Follow the iOpener instructions to avert overheating.

• A hair dryer, heat gun, or hot plate may besides exist used, but be conscientious non to overheat the phone—the display and internal battery are both susceptible to rut damage.

• In the following steps y'all will be cutting through the agglutinative around the edge of the brandish associates.

• Refer to the second and third images and familiarize yourself with the width of the adhesive around edges of the brandish.

• If you plan to re-utilise the display assembly, be particularly careful as you lot cutting the adhesive on the sides of the phone. Don't insert your tool more than than ii mm into the phone, and bending it downwards (abroad from the display assembly) equally much as possible.

• Use a suction cup to the display, near the middle of the left edge.

• Pull the suction cup with business firm, constant pressure to create a slight gap between the display panel and the rear instance.

• If the screen is croaky, the suction cup may not stick. In that case, endeavour lifting with potent tape, or superglue the suction cup in place and permit it to cure and then yous can go along.

• If the display doesn't separate even with significant strength, apply more heat to farther soften the adhesive and try again. The adhesive cools speedily, so yous may demand to estrus it repeatedly.

• Slide the tool along the left edge of the phone, cutting through the adhesive securing the brandish.

• As you move on to cutting the adhesive around the rest of the display, it may help to leave an opening pick in place here and take hold of some other for the post-obit steps.

• Slide the opening pick downwardly and cut the adhesive effectually the bottom of the display.

• If the adhesive is also tough to cut, continue to oestrus it until it softens enough to cut adequately easily. Excessive prying or forcefulness used here could permanently harm the display or other components.

• Be careful as yous slide your choice effectually the top and bottom edges of the display. The brandish cables, fingerprint sensor, and fingerprint sensor cablevision are all housed fairly close to the border of the display and can easily be damaged. Refer to this paradigm to run into the exact location of the cables.

• Keep cutting through the adhesive on the top and right sides of the telephone.

• The proximity sensor, earpiece speaker, and front-facing camera are all located along the top border of the telephone, just are housed below the brandish unit of measurement. You shouldn't come into contact with any of them equally you lot insert your pick to cutting the agglutinative.

• Once all the adhesive is cut, carefully lift open the display from the left border.

• Don't fully remove the display yet. There are even so cables connecting the display assembly that tin can rip hands.

• Prop the display unit of measurement at a ninety degree angle confronting a box to prevent the brandish and fingerprint cables from angle or tearing.

• Remove the yellow sticker covering two of the black Phillips screws below the earpiece.

• Remove the post-obit Phillips screws from the midframe:

• Sixteen three.8 mm black screws

• Three 2.4 mm silver screws

• Insert the apartment end of a spudger between the midframe and the left edge of the telephone and carefully pry to release the two clips belongings the midframe in place.

• Lift the midframe up and abroad from the phone.

• Utilize the indicate of a spudger to disconnect the larger of the two display cable connectors.

• Disconnect the smaller display cable connector.

• This cable houses a display controller fleck encased in yellow tape. You lot do non demand to remove the yellow tape. The fleck is lightly adhered to the motherboard, but should come up with minimal effort.

• Gently keep lifting the cablevision to break the adhesive seal and pull the cable away from the motherboard.

• At the contrary end of the phone, disconnect the fingerprint sensor cablevision.

• The fingerprint sensor cable is taped to a shield in a higher place information technology. As you lift the cable, elevator the tape up with it. You can as well remove the tape before disconnecting the cable.

• Remove the display assembly from the telephone.

• Before you lot reinstall the brandish associates, thoroughly remove any remaining agglutinative and glass from the frame of the device with isopropyl alcohol.

• Be sure to turn on your phone and examination your repair before installing new agglutinative and sealing the brandish associates.

• If your replacement display doesn't have bear on functionality and you're sure that information technology has been installed correctly, back up your information and perform a manufacturing plant reset.

• Remove the yellowish tape covering the battery connector.

• Utilize the point of a spudger to disconnect the battery past prying its connector direct up from the motherboard.

• Pare back the blackness pull tab from the top of the battery and pull straight up with house, steady pressure to interruption the adhesive holding the battery in place.

• The battery is held in place by mulitiple strips of adhesive. Y'all may be able to break the adhesive using the pull tab, but if not, employ an iOpener to the back of the device to soften the adhesive and proceed to the next step.

• If your pull tab breaks or the adhesive is too potent to break, utilise an opening pick to gently pry the battery out of the case.

• Simply pry from the border of the device. Prying from any other side can crusade severe impairment to exposed components.

• Once the battery is loose, remove it from the phone.

• Do non reuse the battery after it has been removed. The stress of removal tin crusade hidden impairment to the battery cell, creating a potential prophylactic take chances. Supervene upon it with a new battery.

• To install a new bombardment:

• Remove any remaining agglutinative from the phone, and clean the entire area nether the battery with isopropyl alcohol.

• Apply a few new strips of pre-cut adhesive or Tesa record.

• If you are attaching the battery with a custom-cut agglutinative, follow this guide.

• Printing the new battery firmly into place for 5-10 seconds.

Team

Embed this guide

Cull a size and re-create the code below to embed this guide as a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Motorola+Moto+G5+Plus+Battery+Replacement/100154

Posted by: pratherfiefultoothe.blogspot.com

Share this post